October/2022 Latest Braindump2go 5V0-21.21 Exam Dumps with PDF and VCE Free Updated Today! Following are some new Braindump2go 5V0-21.21 Real Exam Questions!

QUESTION 20
A company hosts a vSAN 7 stretched cluster for all development workloads. The original sizing of a maximum of 250 concurrent workloads in the vSAN cluster is no longer sufficient and needs to increase to at least 500 concurrent workloads within the next six months. To meet this demand, the original 8-node (4-4-1) cluster has recently been expanded to 16 nodes (8-8-1).
Which three additional steps should the administrator take to support the current growth plans while minimizing the amount of resources required at the witness site? (Choose three.)

A. Add the new vSAN witness appliance to vCenter Server.
B. Deploy a new large vSAN witness appliance at the witness site.
C. Configure the vSAN stretched cluster to use the new vSAN witness.
D. Deploy a new extra large vSAN witness appliance at the witness site.
E. Upgrade the vSAN stretched cluster to vSAN 7.0 U1.
F. Configure the new vSAN witness as a shared witness appliance.

Answer: ABC
Explanation:
Add the appliance to vCenter Server as a witness ESXi host. Make sure to configure the vSAN VMkernel interface on the host.
https://docs.vmware.com/en/VMware-vSphere/7.0/com.vmware.vsphere.vsan-planning.doc/GUID-05C1737A-5FBA-4AEE-BDB8-3BF5DE569E0A.html

Read more

January/2022 Latest Braindump2go 2V0-81.20 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 2V0-81.20 Real Exam Questions!

QUESTION 31
An administrator has added a new ESXi host to a vCenter Server Cluster with NSX-T Data Center already working. The administrator installed NSX-T Data Center components in the new ESXi. When the administrator deploys a new VM in the host, connectivity tests good with ping, but SSH session traffic is erratic. The VDS and NSX-T Data Center configuration is the same as each ESXI in the Cluster, but only VMs in the new ESXI are having problems.
What should the administrator do to address the problem?

A. Verify VLAN connection in each physical uplink.
B. Verify MTU configuration in each physical uplink.
C. Change VDS MTU to 1500 in each physical uplink.
D. Change VDS MTU to 2000 in each physical uplink.

Answer: B
Explanation:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/nsxt_30_install.pdf (144)

Read more

2021/August New Braindump2go 2V0-62.21 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 2V0-62.21 Real Exam Questions!

QUESTION 152
An organization wants to split their Cisco ISE deployment to separate the device administration functionalities from the mam deployment. For this to work, the administrator must deregister any nodes that will become a part of the new deployment, but the button for this option is grayed out. Which configuration is causing this behavior?

A.    One of the nodes is an active PSN.
B.    One of the nodes is the Primary PAN
C.    All of the nodes participate in the PAN auto failover.
D.    All of the nodes are actively being synched.

Answer: B

Read more

2020/October Latest Braindump2go 2V0-41.20 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 2V0-41.20 Real Exam Questions!

QUESTION 34
Which two logical router components span across all transport nodes? (Choose two.)

A. DISTRIBUTED_ROUTER_TIER0
B. SERVICE_ROUTER_TIER0
C. TIER0_DISTRIBUTED_ROUTER
D. DISTRIBUTED_ROUTER_TIER1
E. SERVICE_ROUTER_TIER1

Correct Answer: AD

Read more

2020/June New Braindump2go 3V0-41.19 Exam Dumps with PDF and VCE Free Updated Today! Following are some Real 3V0-41.19 Exam Questions!

QUESTION 21
An architect is helping an organization with the Logical Design of a Layer 2 bridging solution.
This information was gathered during the Assessment Phase:
– Workloads are running on ESXI hosts.
– Workloads are running on KVM hosts.
– Workloads on both type of hypervisors should use bridging services.
– VLAN 50 is used for Tier-0 uplink connectivity.
Which should the architect include in their design?

A. Create an NSX Edge Bridge Cluster and configure the bridging profile with VLAN 60.
B. Create an ESXi Bridge Cluster and configure the bridging profile with VLAN 60.
C. Create an NSX Edge Bridge Cluster and configure the bridging profile with VLAN 50.
D. Create an ESXi Bridge Cluster and configure the bridging profile with VLAN 50.

Read more